Digitally switchable coupling for double tractions. Matching counterpart: Further MK2 on the second vehicle of the double traction.Technical data: voltage: 12-22V DC, maximum current: 90mA, maximum load duration: 10 seconds, bobbin: brass, mechanics: permanent magnet, clutch recording: NEM 362 / NEM 363, buffer distance: approx. 1.5mm shorter than Roco universal coupling, operating temperature : -20 to 80 ° C. The clutch may be max. 10 seconds are loaded.The Digital clutches allow the uncoupling

This design of the adapter board contains voltage regulators for a functional stress of 1.5 V.Adapter board for 21MTC Decoder; The Decoder is plugged into the pin header of the adapter. About large solder pads the wiring within the locomotive CAN be made comfortable. The AdamtC adapter board is equipped with a rectifier that relieves the rectifier of the Decoder, creating this less loss heat and CAN deliver more power for it. Size: 44 x 26.5 x 6 mm.The adapter board Adamtc CAN be used along with

XP 5.1 Function decoder for Next18 interface

This design of the adapter board contains voltage regulators for a functional stress of 5 V.Adapter board for 21MTC Decoder; The Decoder is plugged into the pin header of the adapter. About large solder pads the wiring within the locomotive CAN be made comfortable. The AdamtC adapter board is equipped with a rectifier that relieves the rectifier of the Decoder, creating this less loss heat and CAN deliver more power for it. Size: 44 x 26.5 x 6 mm.The adapter board Adamtc CAN be used along with a

Adapter board for 21MTC Decoder; The Decoder is plugged into the pin header of the adapter. About large solder pads the wiring within the locomotive CAN be made comfortable. The AdamtC adapter board is equipped with a rectifier that relieves the rectifier of the Decoder, creating this less loss heat and CAN deliver more power for it. Size: 44 x 26.5 x 6 mmThe adapter board Adamtc CAN be used along with all 21MTC Decoders, which are a C-type - therefore, MX631C, MX634C, MX638C, MX636C, MX644C, ..

XP 5.1 Function decoder

An important part of the LokSound system is the loudspeaker. Therefore, only specially designed loudspeakers tuned to the sound decoder are used. Here is the old truism: the bigger the speaker, the better the sound. For this reason, speakers are offered in a variety of sizes. An essential accessory is the sound capsule, which gives the loudspeaker diaphragm the necessary sound pressure and is supplied with most loudspeakers. If you are not sure which speaker fits in your model, then we generally

Highly flexible cable, diameter 0.5mm, AWG36, 10m winding, color violet.

Power distributor MoBa distributor V1.2 ready-made module. Thanks to the MoBa distributor V1.2, it is possible to wire conveniently under the model railway system. New consumers or track sections can be quickly supplied with power using the high-quality screw terminals. All terminal points marked with "A" are connected through, just like all points with "B". There is a "B" terminal next to each "A" terminal. This means you can connect your consumers clearly without cable chaos. The status LEDs a

1 amp miniature switching relay, 16 volts. With the small switching relay loads can be switched, which require more power than a function output of the decoder can afford. In this case, simply switch the relay in between. If you want to use a smoke generator, you also need the relay, so that it can work properly.

As your facility grows and you need to connect additional ECoSBoost boosters and ECoSDetector feedbacks to your ECoS or Central Station, you need an ECoSlink terminal. ECoSLink terminal bus distributor plate, 6x Connect sockets, 1x 0.9m cable.

XP 5.1 Function decoder

Finished CAN bus cable with plugs attached on both sides (also called driving cables) in 5 m in length.The Zimo Bus System, based on the industrial-proven CAN protocol, with at least 1000 messages / sec is the most powerful and reliable under Digital system bus systems. The ZIMO system components, such as base units, booster, driveline, magneticle and track section modules, etc., are connected to each other via the CAN bus (Controller Area Network), and wrap it over its traffic with 125 kbit / s

20-pin band cable roll 30m

An important part of the LokSound system is the loudspeaker. Therefore, only specially designed loudspeakers tuned to the sound decoder are used. Here is the old truism: the bigger the speaker, the better the sound. For this reason, speakers are offered in a variety of sizes. An essential accessory is the sound capsule, which gives the loudspeaker diaphragm the necessary sound pressure and is supplied with most loudspeakers. If you are not sure which speaker fits in your model, then we generally

Function decoder MX68 is a special function decoder that does not have a motor output, and whose up to 8 function outputs are mostly used for interior lighting, tail lights and other additional equipment in non-powered vehicles (also as a second receiver in traction vehicles).Function decoder with 8 outputs; in two groups with a maximum total current of 0.4 A each. Possibility of parallel connection of two outputs in order to achieve a higher current via "function mapping".

StayAlive controller with Next18 interface. The STACO2 is designed to equip a model with a Next-18 interface and an energy storage device. A Next-18 decoder can then be plugged onto the STACO2 like an adapter board, which then outputs the decoder connections via 13 soldered wires.Scope of delivery: 1 x STACO2, 14 x 10.4 x 1.9 mm, for controlled charging and discharging of 2 mini gold caps, 13 soldered wires, 2x mini gold caps 1 F/2,7 V, 6,4 x 9,8 (diameter x length), min. 12.5 V - max. 18 V.

StayAlive controller with Next18 interface. The STACO2 is designed to equip a model with a Next-18 interface and an energy storage device. A Next-18 decoder can then be plugged onto the STACO2 like an adapter board, which then outputs the decoder connections via 13 soldered wires.Scope of delivery: 1 x STACO2, 14 x 10.4 x 1.9 mm, for controlled charging and discharging of 2 mini gold caps, 13 soldered wires, 2x mini gold caps 0.3 F/2.7 V, 4 x 12 mm (diameter x length), min. 12.5 V - max. 18 V.

Replacement fitting motor for TR92-101

Tantals for "category 2" decoders (with direct energy storage connection), 15 V variant. Usually a larger number of tantals are connected in parallel: at least 5 are recommended, with MX decoders up to 25, with MS decoders unlimited number.

Replacement plug set for stone module (20pol ribbon cable 2m, 2x crimp plug, 1x 2pol St., 4x 3pol St., 1x size 3pol St., 1x 4pol St.)

Base Equipment MX10EC + Race MX33 + USB Stick + CAN cable + 8pola1m + power supply NG300 + operating instructions (MX10, MX33)

1 x StayAlive controller STACO3B (10x7.3x2mm) for decoders without or with limited provisions for direct energy storage connection. 2 miniature gold caps (solder bridge) can be connected via the two free wires via STACO3B. Suitable for N & TT frame models only.Scope of delivery: 1 x STACO3B, 2 soldered strands, 2x mini gold cap 1 F/2.7 V, 6.4 x 9.8 mm.

1 x Stayalive Controller (10x7,3x2mm) for Decoders without or with an integral precautions for direct energy storage connection. About Staco1 2 or 3 miniature gold caps (solder bridge) CAN be connected via the two free wires. + Scope of delivery: 1x Staco1 and 3x mini-gold caps, 0.3f / 2.7v, 4x12mm