Decoder with wires, 1A.

PD12A-0 vehicle decoder DCC without connection cable, without connector.Operating mode DCC, DC analogDimensions [mm] 24.2 * 11.0 * 2.4Total load capacity 1.0 AMax motor current 1.0AMax. driving voltage 30 V2 light outputs, each dimmable 150 mA2 additional outputs, dimmable 300 mA eachFor optional operation with a conventional direct current driving device or according to the NMRA standard (DCC)Switching between analog and digital operation is automaticDCC Short addresses (1-127), long addresses

A new Doehler & Haass decoder developed exclusively for Modellbahn Union. Two small capacitors are installed on the decoder for driving without data loss. Both the software and the chip itself correspond to the same modern technology as the latest decoders from Doehler & Haass. The decoder, produced in Germany, can be used for both normal DC motors and coreless motors. Switching from analogue to digital operation takes place automatically.The vehicle decoders support braking with asymmetrical di

Doehler & Haass N18-G-2 connection adapter Next18 large with connection cable NEM 652 and with 2 connection strands, length approx. 145 mm.Dimensions [mm] 14.3 * 10.2 * 2.0

Doehler & Haass M21-3 Connection adapter 21-pin interface with 11 connection wires, length approx. 145 mm.Dimensions [mm] (without pins) 15.0 * 16.0 * 0.6Dimensions [mm] (with pins) 15.0 * 16.0 * 6.7

Dimensions [mm] 14.0 * 12.0 * 5.5, impedance 8 ohms, max. power 0.8 W, no sound box required.Installation recommendations:In general, the recommendation is to install the loudspeakers far away from the engine in order to:to avoid inadmissible heating of the loudspeakers andto protect the loudspeaker magnets from demagnetization by the sometimes very strong motor magnets (e.g. Roco).Please note the installation recommendations for the LS1308 speaker:One side of the speaker is the membrane (silver

Dimensions [mm] 15 * 11 * 4.1, impedance 6 ohms, max. power 1.2 W.Installation recommendations:In general, the recommendation is to install the loudspeakers far away from the engine in order to:to avoid inadmissible heating of the loudspeakers and to protect the loudspeaker magnets from demagnetization by the sometimes very strong motor magnets (e.g. Roco).Please note our installation recommendations for the loudspeaker LS1115 or LS1511:One side of the speaker is the membrane (silver finish) sur

Dimensions [mm] 15 * 11 * 3.5, impedance 6 ohms, max. power 1.2 W.Installation recommendations:In general, the recommendation is to install the loudspeakers far away from the engine in order to:to avoid inadmissible heating of the loudspeakers and to protect the loudspeaker magnets from demagnetization by the sometimes very strong motor magnets (e.g. Roco).Please note our installation recommendations for the loudspeaker LS1115 or LS1511:One side of the speaker is the membrane (silver finish) sur

Dimensions [mm] 13 * 8.0 * 2.9, impedance 6 ohms, max. power 1.0 W.Installation recommendations:In general, the recommendation is to install the loudspeakers far away from the engine in order to:to avoid inadmissible heating of the loudspeakers and to protect the loudspeaker magnets from demagnetization by the sometimes very strong motor magnets (e.g. Roco).

Doehler & Haass DH22B-2 Vehicle decoder with ribbon cable NEM 652Operating mode SX1, SX2, DCC, MM, DC analog, AC analogDimensions [mm] (under reserve) 20.7 * 15.8 * 5.2Total load capacity 2.0 AMax motor current 2.0AMax. driving voltage 30 VSwitching voltage with AC-analogue max. 45 V peak = 30 V rms.LV, LR (dimmable) each 150 mAAUX1, AUX2 (dimmable) each 300 mAAUX3, AUX4 each 1.0AAUX5, AUX6 each 1.0AAUX7 1.0AAUX8 unamplifiedwith SUSI interfaceProduct features and functionsFor optional operation

Doehler & Haass DH22B-4 vehicle decoder without connection cableOperating mode SX1, SX2, DCC, MM, DC analog, AC analogDimensions [mm] (under reserve) 20.7 * 15.8 * 5.2Total load capacity 2.0 AMax motor current 2.0AMax. driving voltage 30 VSwitching voltage with AC-analogue max. 45 V peak = 30 V rms.LV, LR (dimmable) each 150 mAAUX1, AUX2 (dimmable) each 300 mAAUX3, AUX4 each 1.0AAUX5, AUX6 each 1.0AAUX7 1.0AAUX8 unamplifiedwith SUSI interfaceProduct features and functionsFor optional operation w

Decoder with cable, 1.5A.

Vehicle decoder 1.5 A (2nd generation) for the 6-pole interface. Strongly reduced dimensions, higher total load capacity and higher motor current (1.5 A), AUX3 and AUX4 as amplified function outputs (1.0 A), AUX5 and AUX6 as unamplified function outputs (alternative to SUSI interface), about five times buffer capacity (therefore longer contact interferences can be passed without data loss). Operating mode SX1, SX2, DCC, MM, DC-analog, total load 1.5 A, maximum motor current 1.5, maximum driving

Cable for connecting SX components, length 2.0 m.

USB cable A / B, length 180 cm.

The newly developed Doehler & Haass sensor replaces the previous Doehler & Haass occupancy detector. It takes over the most important features of its predecessor: 8 track sections, occupancy information in conjunction with all digital systems, adjustable release delay, updating capability. Unlike its predecessor, which only enabled the SX1 locomotive number feedback along with the FCC Digital Center and the Doehler & Haass Power Packs, the new transmitter now supports SX1 locomotive number feedb

With this update for the Lok-Control 2000, it gets the functionality of the TRIX Mobile Station. This means that the SelecTRIX 2 functionalities can be used, provided that a corresponding central unit (TRIX Gleisbox or Central Control 2000 with update chip) is available. A microcontroller is supplied to replace the controller in the Lok-Control 2000. You can do the conversion yourself.

Decoder 8 PINS cable fino NEM652

Decodificador nano con cables muy pequeño

SD16 Fahrzeugsounddecoder NEM652 SX1, SX2, DCC & MM

SD10A Fahrzeugsounddecoder Flachbandkabel NEM Schnittstelle

NEM 651 Decoder Flachbandkabel

N18-G-0 Anschlussadapter Next18 groß ohne Anschlusskabel

PD05A Nano-Lokdecoder ohne Anschlusskabel