Locomotive board for the Zimo-MS950 decoder.8- and 9-pin socket strips34 solder pads, arranged on three sides, for locomotive wiring4 three-pin pin strips for direct connection of servos (servo 1 and -2 are always available, servo 3 and -4 when the SUSI pins are switched to servo operation.Dimensions: 61 x 24.5 x 20 mm (height with MS950 decoder)Delivery without MS950.

Sound Decoder NEM 658 16-pole PLUX16, 19 x 11 x 3.1 mm, with 6 foot outputs, 13 connecting wires (2 x rail, 2 x motor, 2 x acc. Plus, mass, 4 foot outputs, 2 x Speaker), 2 solder pads (other FU outputs).

Decoder MX623F with 6-pin connector NEM651 interface, 20 x 8.5 x 3.5 mm, 0.8 A, 4 function outputs, with SUSI.General properties of ZIMO Decoders: DCC addresses 1 ... 10239, composite addresses 1 ... 9999 (SB 2017, Veren: 127), mm addresses 1 ... 80, functions F0 ... F12 ( .. F20 for sound), 14, 28 or 128 (external) driving steps, 256 or 1024 internal stages, programming the CVS in Service Mode (at the programming track) and in operational mode (with RailCom to acknowledge and read), Uncovered d

Decoder MX622 with strands, 14 x 8 x 2.5 mm, 0.8 A, 4 function outputs, no Susi pins.General properties of ZIMO Decoders: DCC addresses 1 ... 10239, composite addresses 1 ... 9999 (SB 2017, Veren: 127), mm addresses 1 ... 80, functions F0 ... F12 ( .. F20 for sound), 14, 28 or 128 (external) driving steps, 256 or 1024 internal stages, programming the CVS in Service Mode (at the programming track) and in operational mode (with RailCom to acknowledge and read), Uncovered driving (without Decoder r

MN330 digital decoder 1.2A NEM-652 11 stranded wires. Wired variant of the MN330 with 11 connecting wires (2x rail, 2x motor, common plus, ground, elko plus, 4x FA) 9 soldering pads (6x FA, 2x SUSI, 1x switching input or logic level output).Technologically, Zimo non-sound decoders correspond to the MS sound decoders. The identical microcontrollers and largely the same components for the power electronics (motor output stages, etc.) are installed in both product classes, and of course the softwar

MN300 digital decoder 1.0A 11 stranded wires. Wired variant of the MN300, 11 connecting wires (2x rail, 2x motor, common plus, ground, elko plus, 4x FA) 4 soldering pads (2x FA, 2x SUSI).Technologically, Zimo non-sound decoders correspond to the MS sound decoders. The identical microcontrollers and largely the same components for the power electronics (motor output stages, etc.) are installed in both product classes, and of course the software is also (further) developed jointly to a large exten

Base device MX10 + Fahrer MX33 + USB stick + CAN cable + 8pola1m + power supply NG600 + operating instructions (MX10, MX33)

22-pin pin header, counterpart to 21MTC interface

Function Decoder, 14 x 9.5 x 2.1 mm, 0.7 A, 4 function outputs, with NEXT18 interface NEM662.

Functional sound decoder with 21MTC interface for control cars and motorless power cars.21.5 x 15 x 3.6 mm1.2 A total current, duration8 amplified function outputs (FA3 to FA6 switchable to logic level)SUSI pins (SUSI, servo or logic level inputs/outputs)1 switching inputSpeaker output 3 watts / 4-8 ohmsEnergy storage devices (16V electrolytic capacitors or 16V tantalum capacitors) can be connected directly.

MS420 Sound Decoder with 2 additional speaker pins, wired version NEM652.30 x 15.3 x 4 mm1.2 A total and motor current, continuous (2.5 A peak)10 amplified function outputsSUSI pins (SUSI, servo or logic level inputs/outputs)1 switching input2 speaker outputs 1 watt / 8 ohms eachEnergy storage devices (16V electrolytic capacitors or 16V tantalum capacitors) can be connected directly.

MS420 Sound Decoder with 2 additional speaker pins, wired version.30 x 15.3 x 4 mm1.2 A total and motor current, continuous (2.5 A peak)10 amplified function outputsSUSI pins (SUSI, servo or logic level inputs/outputs)1 switching input2 speaker outputs 1 watt / 8 ohms eachEnergy storage devices (16V electrolytic capacitors or 16V tantalum capacitors) can be connected directly.

Sound decoder based on the MS450P22 with 2 additional speaker pins on the PluX22 connector.30 x 15.3 x 4 mm1.2 A total and motor current, continuous (2.5 A peak)10 amplified function outputsSUSI pins (SUSI, servo or logic level inputs/outputs)1 switching input2 speaker outputs 1 watt / 8 ohms eachEnergy storage devices (16V electrolytic capacitors or 16V tantalum capacitors) can be connected directly.

ELKOS for Decoders of Category 2 (with direct energy storage connection), 25 V variant (ie MX Decoder with 21MTX interface). Usually several elkos are connected in parallel: at least 3 recommended, at MX Decoders a maximum of 10 - for the permissible total capacity of 6800 ?F, in MS Decoders unlimited number).Contents: 50 x ELKO 680 ?F / 25 V, 10 x 20 mm (change to ELKOS with higher energy density for availability possible).

Stationary setup module Stein in full equipment, ie: 8 connections for track sections (up to 8 A, HLU, occupation message, etc.), 8 connections for switching drives (double coils, motors) or 16 individual outputs, 16 inputs (div. Sensors, light barriers , Contact tracks, ...), 1 I²C bus, 2 speaker outputs, 2 slots for expansion boards. Included: approx. 2m 20pol ribbon cable incl. 2x 20pol Crimp plug, 4pol plug, 4x 3pol plug Kl., 3pol connector Gr., 2pol plug, instructions.

Basic device MX10 + Fahrer MX33FU + USB stick + CAN cable + 8pola1m + power supply NG600 + operating instructions (MX10, MX33)

8-pin connector board NEM652 for converting to a R-type

Decoder MX635VP with 22-pin PLUX22 interface NEM658, 26 x 15 x 3.5 mm, 1.8 A, 10 function outputs, connection for energy storage 16V (arbitrary capacity, also gold cap), semi-synchronous rectifier for higher motor current and total load capacity (until 1.8a), low voltage source for function outputs (1.5V).General properties of ZIMO Decoders: DCC addresses 1 ... 10239, composite addresses 1 ... 9999 (SB 2017, Veren: 127), mm addresses 1 ... 80, functions F0 ... F12 ( .. F20 for sound), 14, 28 or

22-pin (2 x 11) female strip in raster 1.27 mm, as a mating plug for Decoder with 22-pin or 16-pin PLUX pin strip to pluggle the Decoder in locomas without interface and thus simply make interchangeable. Suitable e.g. For Decoder, which are intended for locomotives with built-in Plux plugs.

Sound Decoder with NEM 658 22-pin PLUX22 interface, 30 x 15 x 4 mm, audio 3 W (4 ohms), 13 Connection wires (2 x rail, 2 x motor, acc. Plus, mass, Elko Plus, 4 FU outputs , 2 x speakers), 6 solder pads (other FU outputs), direct connection energy storage 15 V (unlimited capacity) on Plux pin strip.

4-pin connection cables between Decoder and SUSI module (also for Mxulfa)

1 x StayAlive controller STACO3A (10x7.3x2mm) for decoders without or with limited provisions for direct energy storage connection. 2 miniature gold caps (solder bridge) can be connected via the two free wires via STACO3A. Suitable for N & TT frame models only.Scope of delivery: 1x STACO3A and 2x mini gold caps, 0.3F/2.7V, 4x12mm.

Zimo USB stick, as well as the delivery of the MXulf, as a substitute stick

Double-turn Decoder, 19 x 11 x 3.5 mm, 0.8 A (tip 2.5 A), for 2 double coils, motor or EPL drives, 4 inputs for position feedback or foreclosure, 8 connection wires.The accessory Decoders of the MX820 family are switched to switching and feedback from soft, light and shape signals, magnetic decouplers, etc. Used. The small size allows installation into the track bedding of or in drive housing, for example from LGB turns. All drive types for soft and shape signals are supported by double coils, m